Woodward  5437-845
项目™ ITB集成节气门体包括107 mm、120 mm和135 mm
孔径，设计用于1–2 MW范围内的发动机。这些很大
ITB单元直接连接到伍德沃德项目™ 执行器（电磁，75°装置），从而缓解与连杆相关的问题
对燃气发动机，如非线性和磨损。油门的直接组合
执行器具有良好的低负载稳定性和瞬态特性，以及
无需液压、气动或调速器齿轮系。
（产品规范04162）
执行机构
L系列位置控制器为整个发动机提供了构建块的方法
经营基于微处理器的双向执行器设计
连接到燃油泵、混合器或节气门体。L系列位置控制器
接受位置命令并将0–60度输出轴驱动至
基于内部轴位置传感器的指令位置。高效率
扭矩电机在60°行程范围内提供0.34 Nxm（0.25 lb ft）的标称工作扭矩
燃油或空气控制装置。
（产品规范03328）
项目™ Digital Plus致动器拟安装在发动机上，以控制
各种功能包括（但不限于）：燃油齿条定位、正时控制、，
节流阀和废气旁通阀定位。致动器实际上是一个定位器，具有
一个整体式驱动器，可接受来自其他设备的位置命令信号
速度控制等系统。
ProAct Digital Plus致动器包括一个集成的数字驱动器，能够
控制致动器，与外部控制系统通信，以及
包含车载软件和智能，实现监控和定制
功能。
（产品规范03231）
UG致动器具有电子控制和负载共享的优点
系统，同时使用方便的现有UG8型驱动器和连杆。这个
致动器为伍德沃德模拟控制装置（如2301A）提供肌肉
以及2301和723 Plus等伍德沃德数字控制。UGActuator可用于柴油或天然气发动机，也可用于蒸汽和
工业燃气轮机。UG执行机构有一个独立的油底壳
不需要供油。
（产品规范37511）
PGPL执行器/驱动器是一种带有比例驱动器的电液执行器
可与提供0至200 mA位置的电子控制一起使用的接口
信号致动器设计用于Woodward 2301A和D系列700-
系列，Peak®
150和505数字控制。
（产品规格37520）
空燃比控制单元
LCS空燃比控制为发动机提供的空燃比控制
使用三元催化转化器减少废气排放。[催化剂
同时消除碳氢化合物（HC）、一氧化碳（CO）和
氮（NOx）被称为“三效”催化剂。]
LCS是一种基于微处理器的空燃比控制装置，用于以接近化学计量比的空燃比运行的四冲程汽油发动机。其设计目的是
与三元催化转化器配合使用可有效减少废气排放
排放。通过自动保持佳的空气/燃油混合，排放
实现了合规性，催化剂寿命大化，无需操作员监督。
可在100 kW至250 kW（134
和340马力）。售后套件将适应各种燃料类型和
燃油质量。

The ProAct™ ITB integrated throttle body includes 107 mm, 120 mm, and 135 mm bore sizes, and is designed for use with engines in the 1–2 MW range. These large ITB units are made to couple directly to Woodward’s ProAct™ actuators (an electromagnetic, 75° device), and therefore alleviate the problems associated with linkages on gas engines, such as non-linearity and wear. This direct combination of throttle and actuator results in excellent low-load stability and transient characteristics, and requires no hydraulics, pneumatics, or governor gear train. (product spec 04162) Actuators The L-Series Position Controller provides a building block approach to total engine management. The microprocessor-based bi-directional actuator design easily attaches to fuel pumps, mixers, or throttle bodies. The L-Series Position Controller accepts a position command and drives the 0–60 degree output shaft to the commanded position based on an internal shaft position sensor. The high-efficiency torque motor delivers 0.34 Nxm (0.25 lb-ft) nominally over 60° travel range to operate fuel or air control devices. (product spec 03328) The ProAct™ Digital Plus actuator is intended to be mounted on-engine to control varying functions including (but not limited to): fuel rack positioning, timing control, throttle valve, and wastegate positioning. The actuator is effectively a positioner with an integral driver, which will accept a position command signal from another device in the system such as a speed control. The ProAct Digital Plus actuator includes an integral digital driver capable of controlling the actuator, communicating with the outside control system, and containing on-board software and intelligence to realize monitoring and customizing functions. (product spec 03231) The UG-Actuator offers the advantages of electronic control and load sharing systems while using the convenient, existing UG8-type drives and linkages. The actuator provides the muscle for Woodward analog controls such as the 2301A, as well as Woodward digital controls such as the 2301Dand the 723 Plus. The UGActuator can be used with diesel or natural gas engines, as well as with steam and industrial gas turbines. The UG-Actuator has a self-contained oil sump so a separate oil supply is not required. (product spec 37511) The PGPL Actuator/Driver is an electrohydraulic actuator with a proportional driver interface which can be used with electronic controls providing a 0 to 200 mA position signal. The actuator is designed for use with Woodward 2301A and D series, 700- series, Peak® 150, and 505 digital controls. (product spec 37520) Air-Fuel Ratio Control Units The LCS Air/Fuel Ratio Control provides precise air/fuel ratio control for engines using three-way catalytic converters to reduce exhaust emissions. [A catalyst that simultaneously eliminates hydrocarbons (HC), carbon monoxide (CO), and oxides of nitrogen (NOx) is referred to as a “three-way” catalyst.] The LCS is a microprocessor-based air/fuel ratio control for four-stroke, gaseousfueled engines operating with a near-stoichiometric air/fuel ratio. It is designed to work in conjunction with a three-way catalytic converter to efficiently reduce exhaust emissions. By automatically maintaining an optimum air/fuel mixture, emissions compliance is achieved and catalyst life is maximized without operator supervision. An Aftermarket Kit can be applied on engines between 100 kW and 250 kW (134 and 340 hp). The aftermarket kit will accommodate the full range of fuel types and fuel qualities.