10L-NSD62K04
技术数据（对于这些参数以外的应用，请咨询我们！）1） 大电流Imax可通过“Gw”指令值衰减器电位计设置为所需值。工作电压UB+24 VDC+40%–5%上限值UB（t）ma+35 V下限值UB（t）min+22 V大功耗Ps 50 VA大电流消耗I 1.8 A保险丝为2.5 A缓慢熔断输入指令值1 Ue 0至+9 V（参考电位为M0）指令值2（差动输入）Ue 0至+10 V；Re=100Ω，取决于通过S11至S13或Ie 4至20 mA（负载RB=100Ω）或Ie 0至20 mA（负载RB=100Ω）的设置斜坡时间（设置范围）t 30 ms至约1 s或5 s（取决于通过S14的设置）输出级电磁阀电流/电阻Imax 800 mA+20%，R20=19.5Ω，取决于通过S17 1）或Imax 1600 mA+20%，R20=5.4Ω导频电流，Imax=800 mA，Iv 50 mA或100 mA，取决于Imax=1600 mA，I通过S17和“Zw”（R130）v 100 mA进行的设置，此外，Imax=800 mA，Iv 0至300 mA+20%可通过“Zw”进行调节，Imax=1600 mA，Iv 0至600 mA+20%（R130），印刷电路板时钟频率f 100 Hz，200 Hz，在每种情况下，300 Hz或370 Hz±10%（取决于S25至S27的设置）“准备工作”信号（仅适用于VT-VSPA1-1）高U约UB，50 mA低U 0 V，Ri=10 kΩ调节电压U±9 V±1%，±25 mA外部可加载测量插座命令值“w”U 0至+6 V（+6 V≙ 100%电磁阀电流），Ri=1 kΩ实际电流值“I”U 0至1600 mV≙ 0至1600 mA±20 mA连接类型VT-VSPA1-1 32极外螺纹多点连接器，DIN 41612，设计D VT-VSPA1K-1 16子排卡尺寸欧洲卡100 x 160 mm，DIN 41494前板尺寸高度3 HE（128.4 mm）宽焊接侧1 TE（5.08）宽组件侧3 TE容许工作温度范围 0至+50°C存储温度范围 –25至+85°C重量m 0.1 kg

Technical data (For applications outside these parameters, please consult us!) 1) The maximum current Imax can be set to the required value by means of the "Gw" command value attenuator potentiometer. Operating voltage UB +24 VDC + 40 % – 5 % Upper limit value uB(t)ma +35 V Lower limit value uB(t)min +22 V Max. power consumption Ps 50 VA Max. current consumption I 1.8 A Fuse Is 2.5 A slow-blow Inputs Command value 1 Ue 0 to +9 V (reference potential is M0) Command value 2 (differential input) Ue 0 to +10 V; Re = 100 Ω Depending on the setting by means of S11 to S13 or Ie 4 to 20 mA (load RB = 100 Ω) or Ie 0 to 20 mA (load RB = 100 Ω) Ramp time (setting range) t 30 ms to approx. 1 s or 5 s (depending on the setting by means of S14) Outputs Output stage Solenoid current/resistance Imax 800 mA + 20 %, R20 = 19.5 Ω Depending on the setting by means of S17 1) or Imax 1600 mA + 20 %, R20 = 5.4 Ω Pilot current with Imax = 800 mA Iv 50 mA or 100 mA Depending on the setting by with Imax = 1600 mA I means of S17 and "Zw" (R130) v 100 mA Additionally with Imax = 800 mA Iv 0 to 300 mA + 20 % Adjustable by means of "Zw" with Imax = 1600 mA Iv 0 to 600 mA + 20 % (R130) on the printed circuit board Clock frequency f 100 Hz, 200 Hz, 300 Hz or 370 Hz in each case ±10 % (depending on the setting by means of S25 to S27) "Ready for operation" signal (only with VT-VSPA1-1) High U Approx. UB, 50 mA Low U 0 V, Ri = 10 kΩ Regulated voltage U ±9 V ± 1 %, ± 25 mA externally loadable Measuring sockets Command value "w" U 0 to + 6 V (+6 V ≙ 100 % solenoid current), Ri = 1 kΩ Actual current value "I" U 0 to 1600 mV ≙ 0 to 1600 mA ± 20 mA Type of connection VT-VSPA1-1 32-pole male multipoint connector, DIN 41612, design D VT-VSPA1K-1 16-pole terminal strip Card dimensions Euro-card 100 x 160 mm, DIN 41494 Front plate dimensions Height 3 HE (128.4 mm) Width soldering side 1 TE (5.08) Width component side 3 TE Admissible operating temperature range  0 to +50 °C Storage temperature range  –25 to +85 °C Weight m 0.1 kg