A10V045
订购代码01模拟受控比例压力阀放大器，带一个电磁阀VT-VSPA1 02，带32极外螺纹多点接头，前板无代码，带16子排；无压力阀前板K 03 1 04组件系列10至19（10至19：技术数据和pin分配不变）1X 05更多详细信息，请参阅纯文本*01 02 03 04 05 VT-VSPA1–1–1X/*适用于VT-VSPA1-1的卡座：▶ VT 3002-1-2X/32D型，见数据表29928无电源装置功能的单卡座更换放大器VT 2000（多部件系列4X）、VT 2010、VT 2013或VT 2023时，必须为机架安装单独订购盲板4TE/3HE。材料编号R900021004差动输入（输入2）28（ac）30（ac）u（i）u 0…+10 V/4…20 mA 0…20 mA 0 V参考电位括号内连接名称的修改仅适用于VT-VSPA1-1型。命令值输入2是一个差分输入[1]（0至+10 V）。通过DIL开关2），可将其配置为电流输入（+4至+20 mA或0至+20 mA）。如果命令值由具有不同参考电位的外部电子设备（例如PLC）指定，则必须使用该输入。断开或连接指令值电压时，必须确保两条信号线在每种情况下都与输入分离或连接。在转发之前，将两个命令值相加[2]，然后到达一个电位计[3]，电位计位于卡的前板上，作为衰减器，从而限制大命令值。

Ordering code 01 Amplifi er for controlled proportional pressure valves, analog, with one solenoid VT-VSPA1 02 With 32-pole male multipoint connector and front plate no code With 16-pole terminal strip; without front plate K 03 For pressure valves 1 04 Component series 10 to 19 (10 to 19: Unchanged technical data and pin assignment) 1X 05 Further details in the plain text * 01 02 03 04 05 VT-VSPA1 – 1 – 1X / * Suitable card holders for VT-VSPA1-1: ▶ Type VT 3002-1-2X/32D, see data sheet 29928 Single card holder without power supply unit Function When replacing amplifiers VT 2000 (up to component series 4X), VT 2010, VT 2013 or VT 2023, the blind plate 4TE/3HE must be ordered separately for the rack mounting. Material no. R900021004 Differential input (input 2) 28(ac) 30(ac) u (i) u 0 … +10 V / 4 … 20 mA 0 … 20 mA 0 V reference potential The amendment of the connection designations in brackets only applies to type VT-VSPA1-1. The command value input 2 is a differential input [1] (0 to +10 V). By means of DIL switches 2), it can be configured as current input (+4 to +20 mA or 0 to +20 mA). If the command value is specified by external electronics with a different reference potential (e.g. by a PLC), this input has to be used. When disconnecting or connecting the command value voltage, it has to be ensured that both signal lines are in each case separated from or connected with the input. Before they are forwarded, both command values are summed up [2] and then reach a potentiometer [3] accessible at the front plate of the card which acts as attenuator and thus limits the maximum command value.