MVI69-DNP
在机架中安装模块
如果尚未安装和配置ControlLogix处理器
电源，请在安装MVI模块之前进行此操作。提到
有关安装说明的罗克韦尔自动化产品文档。
警告：安装此电子设备或任何其他电子设备时，必须遵守所有安全说明
设备。不遵守安全程序可能会导致硬件或数据损坏，甚至
人员重伤或死亡。请参阅计划安装的每个设备的文档
在安装或维修之前，连接以验证是否有适当的安全程序
装置
检查跳线位置后，将MVI插入
ControlLogix机箱。使用罗克韦尔推荐的相同技术
自动移除和安装ControlLogix模块。
警告：当您在背板电源打开的情况下插入或卸下模块时，会发生电弧
可能发生。这可能会导致危险位置装置发生爆炸。验证电源是否正常
继续之前，应移除或该区域无危险。重复的电弧原因
模块及其配套接头上的触点过度磨损。磨损的触点可能
产生可能影响模块操作的电阻。
1关闭电源。
2将模块与顶部和底部导轨对齐，然后将其滑入机架
直到模块牢固抵住背板连接器。
3用力平稳推动，将模块卡入到位。
4检查模块顶部和底部的固定夹是否牢固
在机架的锁孔中。
5记下插槽位置。您必须标识
安装模块是为了使示例程序正常工作。狭槽
数字标识在的绿色电路板（背板）上
ControlLogix机架。
6打开电源。
注意：如果插入模块不当，系统可能会停止工作，或者可能会出现以下情况
不可预见地

Installing the Module in the Rack If you have not already installed and configured your ControlLogix processor and power supply, please do so before installing the MVI module. Refer to your Rockwell Automation product documentation for installation instructions. Warning: You must follow all safety instructions when installing this or any other electronic devices. Failure to follow safety procedures could result in damage to hardware or data, or even serious injury or death to personnel. Refer to the documentation for each device you plan to connect to verify that suitable safety procedures are in place before installing or servicing the device. After you have checked the placement of the jumpers, insert MVI into the ControlLogix chassis. Use the same technique recommended by Rockwell Automation to remove and install ControlLogix modules. Warning: When you insert or remove the module while backplane power is on, an electrical arc can occur. This could cause an explosion in hazardous location installations. Verify that power is removed or the area is non-hazardous before proceeding. Repeated electrical arcing causes excessive wear to contacts on both the module and its mating connector. Worn contacts may create electrical resistance that can affect module operation. 1 Turn power OFF. 2 Align the module with the top and bottom guides, and slide it into the rack until the module is firmly against the backplane connector. 3 With a firm but steady push, snap the module into place. 4 Check that the holding clips on the top and bottom of the module are securely in the locking holes of the rack. 5 Make a note of the slot location. You must identify the slot in which the module is installed in order for the sample program to work correctly. Slot numbers are identified on the green circuit board (backplane) of the ControlLogix rack. 6 Turn power ON. Note: If you insert the module improperly, the system may stop working, or may behave unpredictably