MAC90C-0-GD-4C
电源连接/功率段符号UN SMAX IEIN fS ITYP IPEAK PV PBM、DKC PBD、DKC WMAX、DKC WZW、DKC CDKC UZW V kVA kHz A W kW kWs Ws mF V DKC01.1-030-3-FW单相1 x AC 230±10%1,8 10 30 100 5（1秒）0,15 5,0 15 0,15不通向外部三相3 x AC 230±10%3,2 10 12 40 40 180 10（0,5秒）0,15 5,0 15 0,15 DC 500。。。800丹麦克朗**。1-040-7-FW 3 x AC（380…480）4,8。。。9 9 ... 12 4或8±10%fN Hz 50。。。60 4或8 ICONT A 16 ICONT A 11 12,5 TB0202。fh5 f S=4 kHz f S=8 kHz 1）1）2）2）取决于电源输入电压指定的值在电源输入电压大连接处的工作模式。电压使电流开关频率（可选）在额定电流峰值电流功率损耗下的连续电流，无分压器损耗峰值分压器输出DKC连续分压器输出DKC大反馈能量DKC存储能量DKC直流母线电容直流母线电压单位工频连续电流为1）4 kHz和8 kHz切换的驱动数据。频率列于文件“ECODRIVE DKC伺服驱动器”-选择数据中。三相图4-4：电源连接和电源部分的技术数据DC24V电源符号UN，DC w名称DKC输入电压的控制电压连接大纹波含量电流消耗制动装置V%0,7 DC（19,2…28,8）V DKC**。1-040-7-FW不得超过输入电压范围，DC A UN，HB w输入电压电流消耗V%，请参阅MKD dokumentation DC 24±10%，HB A TB0203。fh5大纹波含量不得超过输入电压范围

Power connection / Power section Symbol UN SMAX IEIN fS ITYP IPEAK PV PBM,DKC PBD,DKC WMAX,DKC WZW,DKC CDKC UZW V kVA A kHz A A W kW kW kWs Ws mF V DKC01.1-030-3-FW single-phase 1 x AC 230 ± 10% 1,8 10 30 30 100 5 (for 1 s) 0,15 5,0 15 0,15 not lead to the outside three-phase 3 x AC 230 ± 10% 3,2 10 12 40 40 180 10 (for 0,5 s) 0,15 5,0 15 0,15 DC 500...800 DKC**.1-040-7-FW 3 x AC (380 ... 480) 4,8 ... 9 9 ... 12 4 or 8 ± 10% fN Hz 50...60 4 or 8 ICONT A 16 ICONT A 11 12,5 TB0202.fh5 f S = 4 kHz f S = 8 kHz 1) 1) 2) 2) Value dependent on power input voltage Designation Operating mode at the mains Mains input voltage Maximum conn. voltage Making current Switching frequency (selectable) Continous current at Rated current Peak current Power disspation, without bleeder dissipation Peak bleeder output DKC Continous bleeder output DKC Maximum feedback energy DKC Storage energy DKC DC bus capacitance DC bus voltage Unit Mains frequency Continous current at 1) The drive data for 4 and 8 kHz switching. frequencies are listed in the document "ECODRIVE DKC servo drive" - Selection Data. three-phase Fig. 4-4: Technical data for the power connection and power section DC24V Power supply Symbol UN,DC w Designation Control voltage connection for DKC Input voltage Maximum ripple content Current consumption Voltage connection for holding brake Unit V % 0,7 DC (19,2 ... 28,8) V DKC**.1-040-7-FW must not exceed the input voltage range I N,DC A UN,HB w Input voltage Current consumption V % please see MKD dokumentation DC 24 ± 10% I N,HB A TB0203.fh5 Maximum ripple content must not exceed the input voltage range