KDS1.1-030-300-W0/115
仅适用于电压超过50伏的设备和驱动部件。
接触电压大于50的部件
电压可能很危险。在以下情况下，某些部件处于危险电压下
操作电气设备。
危险
高压！
危及生命或人身伤害的风险！
⇒ 遵守一般施工和安全规定
在电气装置上工作时。
⇒ 接通电源前，确保接地
电线连接至所有电气装置
根据连接图。
⇒ 如果
接地线未连接到
适当的端子，即使是短暂测量或
测验。
⇒ 断开设备与电源线的连接
或开始工作前的电压源。保护
重合闸设备。
⇒ 关闭电源后等待5分钟，让电容器放电，然后再使用设备。
开始工作前测量电容器的电压，以消除以下危险：
触摸组件。
⇒ 电源接通时，切勿触摸部件的电气连接点。
⇒ 在打开设备之前，请盖好带电部件，以免接触到它们。提供的盖子
操作前必须安装设备
防止与带电部件接触的设备。这个
设备只能在带有防电击保护罩的情况下操作。
⇒ GFCI保护装置（接地故障断路器）不能用于交流驱动器！保护
必须通过其他方式确保防止间接接触
指，例如，根据相关标准使用过电流保护装置。
欧洲国家：符合EN
50178/1994，第5.3.2.3节
⇒ 用于安装设备的间接保护
必须使用外部外壳确保接触，
例如控制柜。欧洲国家：根据EN 50178/1994第5.3.2.3节

Only relevant for devices and drive components with voltages exceeding 50 volts. Coming into contact with components carrying voltages greater than 50 volts can be dangerous. Certain parts are under dangerous voltage when operating electrical devices. DANGER High Voltage! Danger to life or risk of bodily injury! ⇒ Follow general construction and safety regulations when working on electrical installations. ⇒ Before switching on power, be sure that the ground wire is permanently connected to all electrical units according to the connection diagram. ⇒ At no time may electrical equipment be operated if the ground wire is not permanently connected to the proper terminals, even for brief measurements or tests. ⇒ Disconnect the equipment from the power supply line or the voltage source before beginning work. Secure equipment from reclosure. ⇒ Wait 5 minutes after switching off power to allow capacitors to discharge before using the equipment. Measure the voltage of the capacitors before beginning work in order to eliminate dangers arising from touching components. ⇒ Never touch the electrical connection points of a component while the power is turned on. ⇒ Cover live parts properly before switching the equipment on so they cannot be touched. Covers provided with the equipment must be installed before operating the equipment to prevent contact with live parts. The equipment may only be operated with the covers designed for shock-hazard protection. ⇒ A GFCI protective device (ground fault circuit interrupter) cannot be used for AC drives! Protection against indirect contact must be ensured by other means, for example, by using an overcurrent protection device in accordance with relevant standards. European countries: in accordance with EN 50178/1994, section 5.3.2.3 ⇒ For installation equipment protection against indirect contact must be ensured using an external housing, such as a control cabinet. European countries: in accordance with EN 50178/1994, section 5.3.2.3