AS-E685-904
检测到系统错误：用户数据的长度规格太大参数\u Siglached Bit 16 E 7129 0检测到系统错误：电机编码器参数\u Warnlached Bit 16 E 712C 0检测到系统错误：无法与编码器通信参数\u Warnlached Bit 16 E 712D 4未找到电子电机铭牌参数\u Siglached Bit 16不正确的电机数据（不正确的CRC）。无电机电子铭牌的电机（如SER电机）联系技术支持或更换电机。E 712F 0未检测到电子电机铭牌的数据段E 7132 0系统错误：无法写入电机配置E 7133 0无法写入电机配置E 7134 4不完整的电机配置参数\u Siglached Bit 16 E 7135 4格式不受支持参数\u Siglached Bit 16 E 7136 4使用参数MotEnctype参数选择的编码器类型不正确\u Siglached在电机配置参数的内部转换过程中检测到位16 E 7137 4错误\u SIGLATCH位16 E 7138 4电机配置参数超出允许范围参数\u SIGLATCH位16 E 7139 0编码器偏移：编码器中的数据段不正确。E 713A 3第三方电机编码器的调整值尚未确定。参数\u Siglached Bit 16 E 7200 4检测到系统错误：制造期间校准模拟/数字转换器/不正确的BLE文件参数\u Siglached Bit 30 E 7320 4检测到系统错误：编码器参数无效\u Siglached Bit 16到编码器的通信信道（Hiperface）受到干扰，电机编码器尚未出厂参数化。联系技术支持。E 7321 3从编码器参数读取位置超时\u SIGLACKED Bit 16通信信道（Hiperface）到编码器受到干扰或电机编码器不工作。检查编码器电缆的接线和屏蔽连接或更换电机。E 7327在Hiperface应答参数中设置了0个错误位\u WarnLatched bit 16 EMC不足。验证接线（屏蔽）。

System error detected: Length specification for user data too great Parameter _SigLatched Bit 16 E 7129 0 System error detected: Motor encoder Parameter _WarnLatched Bit 16 E 712C 0 System error detected: Communication with encoder not possible Parameter _WarnLatched Bit 16 E 712D 4 Electronic motor nameplate not found Parameter _SigLatched Bit 16 Incorrect motor data (incorrect CRC). Motor without electronic motor nameplate (for example, SER motor) Contact Technical Support or replace the motor. E 712F 0 No data segment of the electronic motor nameplate E 7132 0 System error detected: Motor configuration cannot be written E 7133 0 Not possible to write motor configuration E 7134 4 Incomplete motor configuration Parameter _SigLatched Bit 16 E 7135 4 Format is not supported Parameter _SigLatched Bit 16 E 7136 4 Incorrect encoder type selected with parameter MotEnctype Parameter _SigLatched Bit 16 E 7137 4 Error detected during the internal conversion of the motor configuration Parameter _SigLatched Bit 16 E 7138 4 Parameter of the motor configuration out of permissible range Parameter _SigLatched Bit 16 E 7139 0 Encoder offset: Data segment in encoder is incorrect. E 713A 3 Adjustment value of the encoder of the third party motor has not yet been determined. Parameter _SigLatched Bit 16 E 7200 4 System error detected: Calibration analog/digital converter during manufacturing / incorrect BLE file Parameter _SigLatched Bit 30 E 7320 4 System error detected: Invalid encoder parameter Parameter _SigLatched Bit 16 Communication channel (Hiperface) to encoder is subject to interference, motor encoder has not been factoryparameterized. Contact Technical Support. E 7321 3 Timeout reading the absolute position from the encoder Parameter _SigLatched Bit 16 Communication channel (Hiperface) to encoder is subject to interference or motor encoder is inoperative. Verify wiring and shield connection of encoder cable or replace motor. E 7327 0 Error bit set in Hiperface answer Parameter _WarnLatched Bit 16 Insufficient EMC. Verify wiring (shield).