VDI4376
在本地控制模式下，参数IO\U PTtq\U Reference用于设置参考值的来源。 使用参数IO\U PTtq\U reference设置所需的参考值来源。在现场总线控制模式下，参数PTtq\U reference用于设置参考值的来源。 使用参数PTtq\U reference设置所需的参考值来源。偏移和零电压窗口（仅用于模拟输入）可以参考±10V输入值改变目标值的发展： 偏移的参数化 零电压窗口的参数化有关模拟输入的设置，请参阅模块IOM1手册。参数名称HMI菜单HMI名称描述单元小值工厂设置大值数据类型R/W持久专家参数地址通过现场总线IO\U PTtq\U参考配置→ ACGiotq工作模式剖面转矩0参考值源/模拟输入/iAnA：通过模拟输入1的参考值/PTI接口/iPti：通过PTI接口设置的参考值只能在功率级禁用时更改。更改的设置在下次启用功率级时变为活动状态。固件版本可用≥V01.20-0 0 1 UINT16根据CANopen 3005:38h Modbus 1392 Profibus 1392 CIP 105.1.56 ModbusTCP 1392 EtherCAT 3005:38h PROFINET 1392 PTtq\u参考值操作模式配置文件扭矩源0/无：无1/参数“PTtq\u目标”：通过参数PTtq\u目标2的参考值/模拟输入：通过模拟输入3的参考值/PTI接口：通过PTI接口的参考值更改设置变为激活状态立即固件版本可用≥V01.10。-0 1 3 UINT16 R/W--CANopen 301B:38h Modbus 7024 Profibus 7024 CIP 127.1.56 ModbusTCP 7024 EtherCAT 301B:38h PROFINET 7024

e of the Reference Value In local control mode, the parameter IO_PTtq_reference is used to set the source of the reference value.  Set the desired source of the reference value with the parameter IO_PTtq_reference. In fieldbus control mode, the parameter PTtq_reference is used to set the source of the reference value.  Set the desired source of the reference value with the parameter PTtq_reference. Offset and Zero Voltage Window (for Analog Inputs Only) It is possible to change the development of the target value with reference to the ±10V input value:  Parameterization of an offset  Parameterization of a zero voltage window See manual for the module IOM1 for settings for the analog inputs. Parameter name HMI menu HMI name Description Unit Minimum value Factory setting Maximum value Data type R/W Persistent Expert Parameter address via fieldbus IO_PTtq_ reference ConF → ACGiotq Reference value source for operating mode Profile Torque 0 / Analog Input / iAnA: Reference value via analog input 1 / PTI Interface / iPti: Reference value via PTI interface Setting can only be changed if power stage is disabled. Changed settings become active the next time the power stage is enabled. Available with firmware version ≥V01.20. - 0 0 1 UINT16 R/W per. - CANopen 3005:38h Modbus 1392 Profibus 1392 CIP 105.1.56 ModbusTCP 1392 EtherCAT 3005:38h PROFINET 1392 PTtq_reference Reference value source for operating mode Profile Torque 0 / None: None 1 / Parameter 'PTtq_target': Reference value via parameter PTtq_target 2 / Analog Input: Reference value via analog input 3 / PTI Interface: Reference value via PTI interface Changed settings become active immediately. Available with firmware version ≥V01.10. - 0 1 3 UINT16 R/W - - CANopen 301B:38h Modbus 7024 Profibus 7024 CIP 127.1.56 ModbusTCP 7024 EtherCAT 301B:38h PROFINET 7024